IONI specifications overview table

Function	Description
Servo/stepping motor drive	Closed loop control of various types of servo motors by sinusoidal field oriented control with dead-time distortion correction and high dynamic range torque control. Synchronous AC & BLDC motors Sinusoidal and trapezoidal commutated SPM (Surface Permanent Magnet) and IPM (Internal Permanent Magnet) types Brush DC motors Linear motors Iron core Ironless (with external inductive filter) Stepping motor, 2 phase (4,6 or 8 wires)
Control modes	Torque control Velocity/speed control Position control
Setpoint types	See setpoint signal / reference inputs list Direct set-point tracking via pulse and direction, PWM, Analog, Quadrature, SimpleMotion V2 Pulse burst positioning Buffered synchronous motion commands via SimpleMotion V2
Closed loop	Cascaded control loops (PIV): Torque / current control, update frequency 20.0 kHz Velocity control, update frequency 2.5 kHz Position control, update frequency 2.5 kHz
Feed-forwards	Feed-forwards working in velocity & position control modes: Acceleration (inertia canceling) feed-forward Velocity (friction canceling) feed-forward
Homing	Integrated homing function for position control mode: Sensorless hard-stop homing Home switch search Index pulse search Soft position limits (eliminate limit switches)
Feedback devices	See feedback devices list
Safety	Safe torque off with 3-way redundancy Charge pump enable input Stopping motor on errors Tracking error (velocity & position) Over speed error Limit switch DC motor runaway prevention on feedback loss Communication error detection
Protections	Over current Short circuit (phase-to-phase) I2t motor thermal protection Over & under voltage Over temperature
Power supply	Externally supplied IONI, IONI Pro 5 – 52 VDC IONI Pro HC 5 - 55 VDC Additionally an external 5 VDC logic supply required. Note: if drive is used with IONICUBE motherboards, then 24 VDC logic supply voltage is needed instead as IONICUBE has on-board 5V regulator.
Motor output current1	AC/BLDC/Stepping/Linear motors (current specified as peak of sine): IONI 0-15 A IONI Pro 0-18 A IONI Pro HC 0-25 A Brush DC motors: IONI 0-19.5 A IONI Pro 0-23.4 A IONI Pro HC 0-30 A
Commissioning	Granity setup software Online user guide
Compliance	CE (LVD & EMC): EN 61800-5-1:2007, IEC 61000-6-1:2005 and IEC 61000-6-3:2006. Notes: The device is Low Voltage Directive (LVD) compliant up to 42 VDC power supply, and above that level the supply voltage is considered hazardous, so external measures (such as or isolation or protective impedance) are necessary to prevent human contact to any circuit connected to the device. In order to meet EMC standard requirements, a proper installation and wiring is necessary. Refer to user guide for proper installation.
Reliability	MTBF: 2.99 million hours Failure rate (all delivered units, actual statistic from 2015-2017): 0.3%

¹) Currents achievable continuously only with with sufficient coolant air flow. Without forced cooling, typically 30-45% of the maximum range can be driven continuously. Despite of this, maximum current is available for short periods of time even without cooling. Current is automatically throttled on temperature rise to protect the drive.

In no event the Product Information or parts hereof shall be regarded as guarantee of conditions or characteristics. The Product Information or any part thereof may also not be regarded as a warranty of any kind. No liability of any kind shall be assumed by Author with respect to Product Information or any use made by you thereof, nor shall Author indemnify you against or be liable for any third party claims with respect to such information or any use thereof.

As content of this Wiki may be edited by user community, Granite Devices Oy or it's affiliates do not take any responsibility of the contents of this Wiki. Use information at your own risk. However, Granite Devices staff attempts to review all changes made to this Wiki and keep information trustworthy.

Without written consent, Granite Devices' Products or Intellectual Property shall not be used in situations or installations where living beings, material property, or immaterial property could be harmed by the operation, features or failures of Product. Products may only be used in a way where hazards like moving parts, electric shock, laser radiation, or fire can't be realized even if the content of this Wiki would suggest otherwise.