Search results

Create the page "Software" on this wiki! See also the search results found.

Page title matches

Page text matches

• Safe torque off
  *Software (firmware) disabling motor control
  2 KB (302 words) - 12:01, 13 March 2015
• Argon specifications
  #Disable power stage by software @ STO2 input
  10 KB (1,448 words) - 10:42, 5 March 2018
• Homing
  {{tip|Homing is configurable through drive configuration software [[Granity]]. Refer to [[Granity: Goals]] for parameter details. }}
  2 KB (352 words) - 18:20, 4 January 2021
• Argon user guide/Making the first Granity connection
  ...he link: [http://granitedevices.com/assets/files/granity_setup.exe Granity software] for windows (approx 15 MB) # Launch Granity software and:
  2 KB (264 words) - 13:57, 2 June 2015
• Argon user guide/List of things needed
  *[[Controller|Motion controller]]. This may be also a software on a computer.
  2 KB (222 words) - 18:21, 9 December 2015
• GUI
  GUI stands for Graphical User Interface. I.e. software that is displayed on a computer screen.
  94 bytes (16 words) - 13:25, 14 August 2013
• Granity user guide/Uploading a firmware
  ...icle will instruct upgrading the device firmware file by using [[Granity]] software. Uploading a new firmware to the drive using [[Granity]] software may be done by following the steps below.
  2 KB (356 words) - 13:28, 15 May 2015
• Tuning torque controller
  In [[Granity]], there is no dedicated torque control PI gains as the software supports entering motor coil inductance and resistance where the suitable P
  7 KB (1,005 words) - 17:32, 21 October 2015
• Tuning velocity controller
  ...Instead, set acceleration limit from the controller (i.e. settings of CNC software).}}
  9 KB (1,321 words) - 20:54, 28 August 2015
• LinuxCNC
  ...s EMC2 a.k.a. Enhanced Machine Controller, is a popular CNC [[controller]] software that runs on a real-time Linux operating system. LinuxCNC is available for *Can close the position loop inside the software by reading axis position information via [[feedback devices]] and outputtin
  797 bytes (109 words) - 19:57, 28 August 2015
• Actuator
  ...he control system can be simple (a fixed mechanical or electronic system), software-based (e.g. a printer driver, robot control system), or a human or other ag
  548 bytes (86 words) - 19:22, 29 August 2013
• Mach3
  Mach3 is a popular PC CNC [[controller]] software that runs on Windows platforms.
  170 bytes (24 words) - 13:54, 23 July 2015
• Configuring linear servo motor
  This example works with [[Granity]] software. Follow your drive's setup guide for all parts except these:
  4 KB (608 words) - 11:12, 18 June 2016
• Argon specifications overview table
  *[[Granity]] setup software
  3 KB (330 words) - 05:51, 13 September 2017
• Product & Press images
  ==Software==
  2 KB (275 words) - 14:08, 13 October 2020
• IONI specifications overview table
  *[[Granity]] setup software
  3 KB (473 words) - 15:17, 11 February 2021
• Motor not moving troubleshooting
  The suggested actions are described for drives supporting [[Granity]] software. Hoever similar instructions apply to older [[GDtool]] based drives too.
  3 KB (526 words) - 20:12, 28 August 2015
• Troubleshooting VSD-E/XE disabled state
  *Ensure correct pin setup on control software
  3 KB (530 words) - 13:32, 2 September 2014
• Dual-loop feedback position control
  ...-shelf solutions at least [[LinuxCNC]] supports dual-loop operation as the software implements a position controller with feedback input.
  4 KB (572 words) - 19:56, 22 September 2014
• VSD-E/XE firmware releases
  ...must be configured with [[DCtool]] software only. If you mix configuration software and firmware, re-flash firmware to the drive as wrong configuration tool mi
  3 KB (412 words) - 20:47, 9 January 2015

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)