Difference between revisions of "Argon user guide/LED indicators"

[checked revision]

Latest revision as of 16:15, 1 September 2015

LD1 and LD2, blink very briefly during data transmission. Due to short light pulses, these lights appear dimmer than other leds.
LD3 and LD4 have programmed blinking sequences. Sequences consists series of short (S) and long (L) light pulses. For example LLS means the led will blink two long flashs and then one short flash. After sequence there will be a pause before the sequence repeats.
LD3 and LD4 are independent and can show fault and motor state simultaneously. To easier reading sequence, cover one led with a thumb to be able to concentrate to one led.
LD3 and shows the first fault occurred if multiple fault states are active simultaneously.

To see animated images, view this Wiki page in a web browser with animations enabled.

Only LD3 is being controlled by these faults.

Fault reason	LED sequence	LED sequence as text
Hardware		SLLS
Program or memory		SLSL
Internal comm error (unable to establish comm)		SLSS
Internal comm error (in middle of operation)		SSLL
SimpleMotion communication		LSSS
Other/unknown		LLSL

Only LD3 is being controlled by these faults.

Fault reason	LED sequence	LED sequence as text
Hardware		LLSS
Progral or memory		LSLL
Internal comm error (CRC)		LSL
Initialization		LSS
Over current		SLL
Over temperature		LSLS
Over voltage		SLS
Following error		LS
Under voltage		SL
Motion blocked or motor runaway		SSL
Setpoint range exceeded		LSSL
Other/unknown, possibly configuration error such as motor mode Motor typeMT not selected		SSSL

Only LD4 is being controlled by these faults.

Status	LED sequence as text	Motor output powered
Permanent stop (need device reset)	LLS	No
Fault stop (observe LD3 for reason)	Off	Depends on fault
Follow error recovery motion	LS	Yes
Initializing	SL	Yes
Homing	LSS	Yes
Run	On	yes
Other/uncategorized (not any of above). For details, connect with Granity and see status bits.	LLSS	No

@@ Line 1: / Line 1: @@
-{{ArgonManualNav}}Argon has four front panel led indicators which have dedicated indicating tasks:
+{{SetAUGTitle|LED indicators}}{{ArgonManualNav}}Argon has four front panel led indicators which have dedicated indicating tasks:
 *LD1 SimpleMotion transmit led. Blinks when drive transmits data to bus.
 *LD2 SimpleMotion receive led. Blinks when drive receives data from bus.
@@ Line 10: / Line 10: @@
 *LD3 and shows the first fault occurred if multiple fault states are active simultaneously.
 ==List of all LD3 and LD4 sequences==
-To see animations, make sure web browser animations are enabled.
+To see animated images, view this Wiki page in a web browser with animations enabled.
 ===Faults originated from I/O side of drive===
 Only LD3 is being controlled by these faults.
 {| class="wikitable"
 |-
@@ Line 58: / Line 59: @@
 | Setpoint range exceeded || [[File:3LSSL.gif]] || LSSL
 |-
-| Other/unknown, possibly configuration error such as motor mode [[MT]] not selected || [[File:3SSSL.gif]] || SSSL
+| Other/unknown, possibly configuration error such as motor mode {{param|MT}} not selected || [[File:3SSSL.gif]] || SSSL
 |}
@@ Line 78: / Line 79: @@
 |-
 | Run || [[File:4ON.gif]] || On ||yes
+|-
+| Other/uncategorized (not any of above). For details, connect with Granity and see status bits. || [[File:4LLSS.gif]] || LLSS || No
 |}
 [[Category:Argon user guide]]
 [[Category:Argon troubleshooting]]