Argon LED indicators
- LD1 SimpleMotion transmit led. Blinks when drive transmits data to bus.
- LD2 SimpleMotion receive led. Blinks when drive receives data from bus.
- LD3 Fault indicator
- LD4 Motor control state indicator
How to read indications
- LD1 and LD2, blink very briefly during data transmission. Due to short light pulses, these lights appear dimmer than other leds.
- LD3 and LD4 have programmed blinking sequences. Sequences consists series of short (S) and long (L) light pulses. For example LLS means the led will blink two long flashs and then one short flash. After sequence there will be a pause before the sequence repeats.
- LD3 and LD4 are independent and can show fault and motor state simultaneously. To easier reading sequence, cover one led with a thumb to be able to concentrate to one led.
- LD3 and shows the first fault occurred if multiple fault states are active simultaneously.
List of all LD3 and LD4 sequences
To see animated images, view this page in a web browser with animations enabled.
Faults originated from I/O side of drive
Only LD3 is being controlled by these faults.
| Fault reason | LED sequence | LED sequence as text |
|---|---|---|
| Hardware |  |
SLLS |
| Program or memory |  |
SLSL |
| Internal comm error (unable to establish comm) |  |
SLSS |
| Internal comm error (in middle of operation) |  |
SSLL |
| SimpleMotion communication |  |
LSSS |
| Other/unknown |  |
LLSL |
Faults originated from GraniteCore side of drive
Only LD3 is being controlled by these faults.
| Fault reason | LED sequence | LED sequence as text |
|---|---|---|
| Hardware |  |
LLSS |
| Progral or memory |  |
LSLL |
| Internal comm error (CRC) |  |
LSL |
| Initialization |  |
LSS |
| Over current |  |
SLL |
| Over temperature |  |
LSLS |
| Over voltage |  |
SLS |
| Following error |  |
LS |
| Under voltage |  |
SL |
| Motion blocked or motor runaway | |
SSL |
| Setpoint range exceeded |  |
LSSL |
| Other/unknown, possibly configuration error such as motor mode MT not selected |  |
SSSL |
Motor control states
Only LD4 is being controlled by these faults.
| Status | LED sequence | LED sequence as text | Motor output powered |
|---|---|---|---|
| Permanent stop (need device reset) |  |
LLS | No |
| Fault stop (observe LD3 for reason) |  |
Off | Depends on fault |
| Follow error recovery motion |  |
LS | Yes |
| Initializing |  |
SL | Yes |
| Homing |  |
LSS | Yes |
| Run |  |
On | yes |
In no event the Product Information or parts hereof shall be regarded as guarantee of conditions or characteristics. The Product Information or any part thereof may also not be regarded as a warranty of any kind. No liability of any kind shall be assumed by Author with respect to Product Information or any use made by you thereof, nor shall Author indemnify you against or be liable for any third party claims with respect to such information or any use thereof.
As content of this Wiki may be edited by user community, Granite Devices Oy or it's affiliates do not take any responsibility of the contents of this Wiki. Use information at your own risk. However, Granite Devices staff attempts to review all changes made to this Wiki and keep information trustworthy.
Without written consent, Granite Devices' Products or Intellectual Property shall not be used in situations or installations where living beings, material property, or immaterial property could be harmed by the operation, features or failures of Product. Products may only be used in a way where hazards like moving parts, electric shock, laser radiation, or fire can't be realized even if the content of this Wiki would suggest otherwise.
