Difference between revisions of "SimuCUBE LED indicators"

Revision as of 13:42, 25 May 2016 (edit) Esa (Talk | contribs) ← Older edit		Latest revision as of 13:20, 28 February 2018 (edit) (undo) Mtakala (Talk | contribs) m (→‎SimuCUBE LED indicators)
(6 intermediate revisions by 2 users not shown)
Line 1:		Line 1:
		+	{{SimucubeManualNav}}SimuCUBE system has two sets of leds: one set on SimuCUBE board and another set in the plugged IONI drive.
		+
	== IONI ==		== IONI ==
	For IONI LED status indicators, please refer to [[IONI & IONICUBE user guide/LED indicators|IONI LED indicators]].		For IONI LED status indicators, please refer to [[IONI & IONICUBE user guide/LED indicators|IONI LED indicators]].
	== SimuCUBE ==		== SimuCUBE ==
−	{{picturebox|simucube_LED_indicators.jpg|caption=SimuCUBE LED indicators.}}	+	[[File:simucube_LED_indicators.jpg|thumb|800px|center|SimuCUBE LED indicators.]]
	=== SimuCUBE LED indicators===		=== SimuCUBE LED indicators===
Line 10:		Line 12:
	|-		|-
	!  LED # !! Color || Indication		!  LED # !! Color || Indication
		+	!Technical information
	|-		|-
−	| LED3 || Green || +3.3 V logic voltage is ok.	+	| LED3 || Green || Power on
		+	|Lit when on board 3.3V signal power is on
	|-		|-
−	| LED4 || Green || FirmWare related. Connected to STM32F4 I/O pin PD15. Mmos: torque clipping.	+	| LED4 || Green || MMOS: Clipping led. SimuCUBE Firmware: Clipping led.
		+	|Connected to STM32F4 I/O pin PD15.
	|-		|-
−	| LED5 || Red || Firmware related. Connected to STM32F4 I/O pin PD14.	+	| LED5 || Red || Firmware controlled, TBA
		+	|Connected to STM32F4 I/O pin PD14
	|-		|-
−	| LED4 || Green || Firmware related. Connected to STM32F4 I/O pin PD13.	+	| LED6 || Green || Firmware controlled, TBA
		+	|Connected to STM32F4 I/O pin PD13
	|}		|}
−		+	[[Category:SimuCUBE_user_guide]]
−	{{next|[[:Category:SimuCUBE troubleshooting|Troubleshooting]]}}	+
−		+
	[[Category:SimuCUBE]]		[[Category:SimuCUBE]]
−	[[Category:SimuCUBE_user_guide]]

---

Latest revision as of 13:20, 28 February 2018

SimuCUBE documentation

---

SimuCUBE main board information

• About SimuCUBE
• Technical specifications
• List of hardware needed
• Connector pinouts and wiring
• LED status indicators

SimuCUBE acrylic enclosures

• Assembling SimuCUBE 320W kit
• Assembling SimuCUBE 480W/720W kit

SimuCUBE install guide

• PART 0: Overview
• PART 1: Connecting motor
• PART 2: Motor configuration
• PART 3: Installing firmware
• PART 4: Connecting pedals and buttons

Extra information

• Troubleshooting
• Glossary

Contents

• 1 IONI
• 2 SimuCUBE
  • 2.1 SimuCUBE LED indicators

SimuCUBE system has two sets of leds: one set on SimuCUBE board and another set in the plugged IONI drive.

IONI[edit | edit source]

For IONI LED status indicators, please refer to IONI LED indicators.

SimuCUBE[edit | edit source]

SimuCUBE LED indicators[edit | edit source]

LED #	Color	Indication	Technical information
LED3	Green	Power on	Lit when on board 3.3V signal power is on
LED4	Green	MMOS: Clipping led. SimuCUBE Firmware: Clipping led.	Connected to STM32F4 I/O pin PD15.
LED5	Red	Firmware controlled, TBA	Connected to STM32F4 I/O pin PD14
LED6	Green	Firmware controlled, TBA	Connected to STM32F4 I/O pin PD13