Difference between revisions of "Argon user guide/Mating connectors and accessories"

From Granite Devices Knowledge Wiki
Jump to: navigation, search
[checked revision][checked revision]
(→‎Braking resistors)
(→‎Braking resistors)
 
(5 intermediate revisions by the same user not shown)
Line 121: Line 121:
 
! Description !! Manufacturer || Part number !! Distributors and order codes
 
! Description !! Manufacturer || Part number !! Distributors and order codes
 
|-
 
|-
−
| Half brick heatsink. Up to 4 pcs of standard half brick heat sinks can be fitted to a drive to improve cooling and increase maximum power output. Install with thermal grease. Note: M3 mounting screws must not reach through the 5 mm thick heat sink of the drive! || CUI Inc || VHS-95 ||  
+
| Half brick heatsink. Up to 4 pcs of standard half brick heat sinks can be fitted to a drive to improve cooling and increase maximum power output. Install with thermal grease. Note: M3 mounting screws must not reach through the 5 mm thick heat sink of the drive! || Wakefield || 518-95AB ||  
−
*[[Granite Devices web shop|GD web shop]]
+
*{{Digikey |345-1055-ND}}
−
*{{Digikey |102-1489-ND}}
+
 
|-
 
|-
 
| Fuse, anti-surge, 6.3A. A replacement for original fuse in the drive. See [[replacing Argon fuse]]. || SCHURTER || 0001.2512 || {{Farnell|1360860}}
 
| Fuse, anti-surge, 6.3A. A replacement for original fuse in the drive. See [[replacing Argon fuse]]. || SCHURTER || 0001.2512 || {{Farnell|1360860}}
Line 154: Line 153:
 
==[[Argon user guide/Braking resistor|Braking resistors]]==
 
==[[Argon user guide/Braking resistor|Braking resistors]]==
 
{{tip|One resistor in a multiaxis system may be sufficient if drives are [[Argon_user_guide/J4_connector_wiring|wired to share the HV DC bus between them]]}}
 
{{tip|One resistor in a multiaxis system may be sufficient if drives are [[Argon_user_guide/J4_connector_wiring|wired to share the HV DC bus between them]]}}
−
{{tip|In most installations braking resistor is not needed at all. Resistor is needed in cases where fast moving motor with high inertial load is stopped rapidly causing conversion of the kinetic energy into electric current which needs to be dissipated by a resistor. Experimenting without resistor is safe as drive's overvoltage protection will prevent any damage occurring. If drive faults to overvoltage fault during deceleration, then try adjusting [[FOV]] to higher value or add a braking resistor.}}
+
{{tip|In most installations braking resistor is not needed at all. Resistor is needed in cases where fast moving motor with high inertial load is stopped rapidly causing conversion of the kinetic energy into electric current which needs to be dissipated by a resistor. Experimenting without resistor is safe as drive's overvoltage protection will prevent any damage occurring. If drive faults to overvoltage fault during deceleration, then try adjusting {{param|FOV}} to higher value or add a braking resistor.}}
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 167: Line 166:
 
*[[Granite Devices web shop|GD web shop]]
 
*[[Granite Devices web shop|GD web shop]]
 
*{{digikey|A102370-ND}}
 
*{{digikey|A102370-ND}}
 +
|-
 +
|100 ohm 150W braking resistor for 220-240VAC installation || Arcol || HS150100RJ ||
 +
*{{farnell|2504896}}
 
|}
 
|}

Latest revision as of 15:45, 24 November 2015

Argon general pages
Argon user guide
This page lists available mating connectors, accessories and spare parts for Argon (servo drive). Most parts or equivalents are available from large number of distributors. Feel free to extend this list.

Connectors[edit | edit source]

J1 connector[edit | edit source]

Description Manufacturer Part number Distributors and order codes
PLUG, D, SOLDER, 15WAY MULTICOMP 5501-15PA-02-F1
DE, US,UK,ES,FR,FI,SE,IT

Accessories[edit | edit source]

Description Manufacturer Part number Distributors and order codes
D-SUB BACKSHELL, 15WAY MH CONNECTORS DPPK15-GREY-K
DE, US,UK,ES,FR,FI,SE,IT

J2 connector[edit | edit source]

Cable assemblies[edit | edit source]

Cable used for J2 should be shielded (S/FTP or FTP, not UTP) type.

Description Manufacturer Part number Distributors and order codes
Premium patch cable 0.5m VIDEK 3962-0.5 Farnell 1525999
DE, US,UK,ES,FR,FI,SE,IT
Premium patch cable 1m VIDEK 3962-1
Premium patch cable 2m VIDEK 3962-2 Farnell 1525753
DE, US,UK,ES,FR,FI,SE,IT
Premium patch cable 5m VIDEK 3962-5 Farnell 1525755
DE, US,UK,ES,FR,FI,SE,IT
Premium patch cable 10m VIDEK 3962-10
Shielded patch cable 0.5m VIDEK 2992-0.5 Farnell 1517504
DE, US,UK,ES,FR,FI,SE,IT
Shielded patch cable 1m VIDEK 2992-1
Shielded Patch cable 2m VIDEK 2992-2 Farnell 1517506
DE, US,UK,ES,FR,FI,SE,IT
Shielded patch cable 5m VIDEK 2992-5 Farnell 1517509
DE, US,UK,ES,FR,FI,SE,IT
Shielded patch cable 10m VIDEK 2992-10
Shielded patch cable 0.5m Assman A-MCSP-80005/B-R Digikey A-MCSP-80005/B-R
Shielded patch cable 1m Assman A-MCSP-80005/Y-R Digikey A-MCSP-80010/Y-R
Shielded patch cable 2m Assman A-MCSP-80020/Y-R Digikey A-MCSP-80020/Y-R
Shielded patch cable 3m Assman A-MCSP-80050/Y-R Digikey A-MCSP-80030/Y-R
Shielded patch cable 5m Assman A-MCSP-80050/Y-R Digikey A-MCSP-80050/Y-R
Shielded patch cable 10m Assman A-MCSP-80050/Y-R Digikey A-MCSP-80100/Y-R

Accessories[edit | edit source]

Description Manufacturer Part number Distributors and order codes
RJ45 break-out board with DIN rail fixutre (convert RJ45 to screw terminals). Helpful for wiring STO and Enable wires. Camden boss CIM/RJ45 Farnell 2211819
DE, US,UK,ES,FR,FI,SE,IT

J3 connector[edit | edit source]

This part is included with Argon package.

Description Manufacturer Part number Distributors and order codes
3 pole 0.2" pitch terminal On Shore Technology Inc OSTTJ035153

J4 connector[edit | edit source]

This part is included with Argon package.

Description Manufacturer Part number Distributors and order codes
10 pole 0.2" pitch terminal On Shore Technology Inc OSTTJ105153

J5 connector[edit | edit source]

Example of DIN rail attachable IDC terminal block/breakout board.

Mating connector type is 0.1" pitch 26 pin IDC ribbon cable socket, see example (pdf).

Description Manufacturer Part number Distributors and order codes
SOCKET, IDC, 2.54MM, 26WAY AMPHENOL T812126A100CEU
DE, US,UK,ES,FR,FI,SE,IT
SOCKET, IDC, WITH S/RELIEF, 26WAY MULTICOMP MC6FD026-30P1
DE, US,UK,ES,FR,FI,SE,IT

Accessories[edit | edit source]

Description Manufacturer Part number Distributors and order codes
IDC terminal block, 26WAY Camden boss CIM/202426W-IDCS
DE, US,UK,ES,FR,FI,SE,IT

Heat sinks & cooling & high power application[edit | edit source]

Description Manufacturer Part number Distributors and order codes
Half brick heatsink. Up to 4 pcs of standard half brick heat sinks can be fitted to a drive to improve cooling and increase maximum power output. Install with thermal grease. Note: M3 mounting screws must not reach through the 5 mm thick heat sink of the drive! Wakefield 518-95AB
Fuse, anti-surge, 6.3A. A replacement for original fuse in the drive. See replacing Argon fuse. SCHURTER 0001.2512 Farnell 1360860
DE, US,UK,ES,FR,FI,SE,IT
Fuse, anti-surge, 10A. A higher power alternative fuse. See replacing Argon fuse. SCHURTER 0001.2514 Farnell 1360862
DE, US,UK,ES,FR,FI,SE,IT
Fuse, anti-surge, 16A. A higher power alternative fuse. See replacing Argon fuse. SCHURTER 0034.3129 Farnell 1360824
DE, US,UK,ES,FR,FI,SE,IT

Electromagnetic interference filtering[edit | edit source]

Multiple drives may be connected behind one power line filter as long as total current consumption doesn't exceed filter rating
Description Manufacturer Part number Distributors and order codes
EMI suppression core for low frequency band Laird LFB159079-000 Digikey 240-2281-ND
EMI suppression core for medium frequency band Laird 28B0616-000 Digikey 240-2306-ND
Power line filter for up to 12A AC input current, FN2090 series - low cost Schaffner FN2090-12-06 Digikey 817-1332-ND
Power line filter for up to 16A AC input current, FN241x series - high performance Schaffner FN2412-16-44 Digikey 817-1358-ND
Power line filter for up to 12A AC input current, FN350 series - optimal for single phase motor drives Schaffner FN350-12-29 Digikey 817-1130-ND
Power line filter for up to 20A AC input current, FN350 series - optimal for single phase motor drives Schaffner FN350-20-29 Digikey 817-1131-ND

Braking resistors[edit | edit source]

One resistor in a multiaxis system may be sufficient if drives are wired to share the HV DC bus between them
In most installations braking resistor is not needed at all. Resistor is needed in cases where fast moving motor with high inertial load is stopped rapidly causing conversion of the kinetic energy into electric current which needs to be dissipated by a resistor. Experimenting without resistor is safe as drive's overvoltage protection will prevent any damage occurring. If drive faults to overvoltage fault during deceleration, then try adjusting Over voltage fault thresholdFOV to higher value or add a braking resistor.
Description Manufacturer Part number Distributors and order codes
82 ohm 250W braking resistor for 220-240VAC installation Tyco Tyco HSC 250 82R
DE, US,UK,ES,FR,FI,SE,IT
47 ohm 250W braking resistor for 110-120VAC installation Tyco Tyco HSC 250 47RJ Farnell 1619349
DE, US,UK,ES,FR,FI,SE,IT
100 ohm 150W braking resistor for 220-240VAC installation TE Connectivity 1630012-1
100 ohm 150W braking resistor for 220-240VAC installation Arcol HS150100RJ
DE, US,UK,ES,FR,FI,SE,IT
Retrieved from "https://granitedevices.com/w/index.php?title=Argon_user_guide/Mating_connectors_and_accessories&oldid=4717"