Difference between revisions of "Argon user guide/Mating connectors and accessories"
From Granite Devices Knowledge Wiki
[checked revision] | [checked revision] |
(→Heat sinks & cooling & high power application) |
(→Braking resistors) |
||
Line 152: | Line 152: | ||
=[[Argon user guide/Braking resistor|Braking resistors]]= | =[[Argon user guide/Braking resistor|Braking resistors]]= | ||
− | {{tip|One resistor in a multiaxis system may be sufficient if drives are [[ | + | {{tip|One resistor in a multiaxis system may be sufficient if drives are [[Argon_user_guide/J4_connector_wiring|wired to share the HV DC bus between them]]}} |
{| class="wikitable" | {| class="wikitable" | ||
|- | |- |
Revision as of 16:15, 26 February 2014
This page lists available mating connectors, accessories and spare parts for Argon (servo drive). Most parts or equivalents are available from large number of distributors. Feel free to extend this list.Connectors
J1 connector
Description | Manufacturer | Part number | Distributors and order codes |
---|---|---|---|
PLUG, D, SOLDER, 15WAY | MULTICOMP | 5501-15PA-02-F1 |
|
Accessories
Description | Manufacturer | Part number | Distributors and order codes |
---|---|---|---|
D-SUB BACKSHELL, 15WAY | MH CONNECTORS | DPPK15-GREY-K |
|
J2 connector
Cable assemblies
Cable used for J2 should be shielded (S/FTP or FTP, not UTP) type and preferrably with standed wires.
Description | Manufacturer | Part number | Distributors and order codes |
---|---|---|---|
Premium patch cable 0.5m | VIDEK | 3962-0.5 | Farnell 1525999 |
Premium patch cable 1m | VIDEK | 3962-1 | |
Premium patch cable 2m | VIDEK | 3962-2 | Farnell 1525753 |
Premium patch cable 5m | VIDEK | 3962-5 | Farnell 1525755 |
Premium patch cable 10m | VIDEK | 3962-10 | |
Shielded patch cable 0.5m | VIDEK | 2992-0.5 | Farnell 1517504 |
Shielded patch cable 1m | VIDEK | 2992-1 | |
Shielded Patch cable 2m | VIDEK | 2992-2 | Farnell 1517506 |
Shielded patch cable 5m | VIDEK | 2992-5 | Farnell 1517509 |
Shielded patch cable 10m | VIDEK | 2992-10 | |
Shielded patch cable 0.5m | Assman | A-MCSP-80005/B-R | Digikey A-MCSP-80005/B-R |
Shielded patch cable 1m | Assman | A-MCSP-80005/Y-R | Digikey A-MCSP-80010/Y-R |
Shielded patch cable 2m | Assman | A-MCSP-80020/Y-R | Digikey A-MCSP-80020/Y-R |
Shielded patch cable 3m | Assman | A-MCSP-80050/Y-R | Digikey A-MCSP-80030/Y-R |
Shielded patch cable 5m | Assman | A-MCSP-80050/Y-R | Digikey A-MCSP-80050/Y-R |
Shielded patch cable 10m | Assman | A-MCSP-80050/Y-R | Digikey A-MCSP-80100/Y-R |
Accessories
Description | Manufacturer | Part number | Distributors and order codes |
---|---|---|---|
RJ45 break-out board with DIN rail fixutre (convert RJ45 to screw terminals). Helpful for wiring STO and Enable wires. | Camden boss | CIM/RJ45 | Farnell 2211819 |
J3 connector
This part is included with Argon package.
Description | Manufacturer | Part number | Distributors and order codes |
---|---|---|---|
3 pole 0.2" pitch terminal | On Shore Technology Inc | OSTTJ035153 |
J4 connector
This part is included with Argon package.
Description | Manufacturer | Part number | Distributors and order codes |
---|---|---|---|
10 pole 0.2" pitch terminal | On Shore Technology Inc | OSTTJ105153 |
|
J5 connector
Mating connector type is 0.1" pitch 26 pin IDC ribbon cable socket, see example (pdf).
Description | Manufacturer | Part number | Distributors and order codes |
---|---|---|---|
SOCKET, IDC, 2.54MM, 26WAY | AMPHENOL | T812126A100CEU |
|
SOCKET, IDC, WITH S/RELIEF, 26WAY | MULTICOMP | MC6FD026-30P1 |
|
Accessories
Description | Manufacturer | Part number | Distributors and order codes |
---|---|---|---|
IDC terminal block, 26WAY | Camden boss | CIM/202426W-IDCS |
|
Heat sinks & cooling & high power application
Description | Manufacturer | Part number | Distributors and order codes |
---|---|---|---|
Half brick heatsink. Up to 4 pcs of standard half brick heat sinks can be fitted to a drive to improve cooling and increase maximum power output. Install with thermal grease. Note: M3 mounting screws must not reach through the 5 mm thick heat sink of the drive! | CUI Inc | VHS-95 | |
Fuse, anti-surge, 6.3A. A replacement for original fuse in the drive. See replacing Argon fuse. | SCHURTER | 0001.2512 | Farnell 1360860 |
Fuse, anti-surge, 10A. A higher power alternative fuse. See replacing Argon fuse. | SCHURTER | 0001.2514 | Farnell 1360862 |
Fuse, anti-surge, 16A. A higher power alternative fuse. See replacing Argon fuse. | SCHURTER | 0034.3129 | Farnell 1360824 |
Electromagnetic interference filtering
Multiple drives may be connected behind one power line filter as long as total current consumption doesn't exceed filter rating |
Description | Manufacturer | Part number | Distributors and order codes |
---|---|---|---|
EMI suppression core for low frequency band | Laird | LFB159079-000 | Digikey 240-2281-ND |
EMI suppression core for medium frequency band | Laird | 28B0616-000 | Digikey 240-2306-ND |
Power line filter for up to 12A AC input current, FN2090 series - low cost | Schaffner | FN2090-12-06 | Digikey 817-1332-ND |
Power line filter for up to 16A AC input current, FN241x series - high performance | Schaffner | FN2412-16-44 | Digikey 817-1358-ND |
Power line filter for up to 12A AC input current, FN350 series - optimal for single phase motor drives | Schaffner | FN350-12-29 | Digikey 817-1130-ND |
Power line filter for up to 20A AC input current, FN350 series - optimal for single phase motor drives | Schaffner | FN350-20-29 | Digikey 817-1131-ND |
Braking resistors
One resistor in a multiaxis system may be sufficient if drives are wired to share the HV DC bus between them |
Description | Manufacturer | Part number | Distributors and order codes |
---|---|---|---|
82 ohm 250W braking resistor for 220-240VAC installation | Tyco | Tyco HSC 250 82R | Farnell 1619350 |
47 ohm 250W braking resistor for 220-240VAC installation | Tyco | Tyco HSC 250 47RJ | Farnell 1619349 |