Help
Book creator (disable)

Difference between revisions of "SimuCUBE pinouts and wiring"

From Granite Devices Knowledge Wiki
Jump to: navigation, search
[checked revision][checked revision]
m (→‎External connectors)
m
Line 1: Line 1:
 
{{SimucubeManualNav}}
 
{{SimucubeManualNav}}
−
==External connectors==
+
==External connectors==  
 
[[File:Simucubeconnectors.jpg|800px|thumb|center|Overview of external SimuCUBE connectors.]]
 
[[File:Simucubeconnectors.jpg|800px|thumb|center|Overview of external SimuCUBE connectors.]]
  

Revision as of 12:56, 28 February 2018

SimuCUBE documentation

SimuCUBE main board information

SimuCUBE acrylic enclosures

SimuCUBE install guide

Extra information

External connectors

Overview of external SimuCUBE connectors.

Legend

Color
Supply pin
Input pin
Output pin

X1 - Motor & E-stop connector

Pin number Signal name Usage
1 U / PH1 Motor phase 1 / Servo U
2 V / PH2 Motor phase 2 / Servo V
3 W / PH3 Motor phase 3 / Servo W
4 PH4 Motor phase 4
5 GND Ground voltage (0 V) of the SimuCUBE, shield
6 E-Stop / STO External stop / Safe Torque Off input pin (active high)
7 +5 V 5 V supply voltage

X16 - Motor position sensor connector

A, B, and C indicate the quadrature encoder differential signals.

Pin # Pin name Electrical type (in most feedback device modes)
Shell GND Earth / 0 V
1 HALL_W Hall sensor digital input W
2 HALL_V Hall sensor digital input V
3 HALL_U Hall sensor digital input U
4 GND Encoder supply ground / 0 V
5 B- Encoder differential input B-
6 B+ Encoder differential input B+
7 A- Encoder differential input A-
8 A+ Encoder differential input A+
9 5V_OUT Encoder supply +5 V output
10 GND Encoder supply ground / 0 V
11 GPI3 IONI GPI3 input
12 GPI2 IONI GPI2 input
13 GPI1 IONI GPI1 input
14 C- Encoder differential input C-
15 C+ Encoder differential input C+

X12-upper

Pin 1 is the right-most. These are active-low with an internal 3.3 kOhm pull-up resistor.
Use with a RJ45 (8P8C) modular connector. Can be used with straight unshielded or shielded CAT3/5/5e cables (don't use crossover cables!)

Pin number Signal name STM32F407 pin Usage
1 Button 1 PC11 Digital input for button
2 Button 2 PC6 Digital input for button
3 Button 3 PC7 Digital input for button
4 Button 4 PC8 Digital input for button
5 Button 5 PC9 Digital input for button
6 Button 6 PE5 Digital input for button
7 Button 7 PC10 Digital input for button
8 GND / 0 V Ground

X12-lower

Pin 1 is the left-most. These are active-low with an internal 3.3 kOhm pull-up resistor.
Use with a RJ45 (8P8C) modular connector. Can be used with straight unshielded or shielded CAT3/5/5e cables (don't use crossover cables!)

Pin number Signal name STM32F407 pin Usage
1 Button 8 PE2 Digital input for button
2 Button 9 PE3 Digital input for button
3 Button 10 PE1 Digital input for button
4 Button 11 PE0 Digital input for button
5 Button 12 PC12 Digital input for button
6 Button 13 PC13 Digital input for button
7 Button 14 PC14 Digital input for button
8 GND / 0 V Ground

X11-upper

Pin 1 is the right-most.
Use with a RJ45 (8P8C) modular connector. Can be used with straight unshielded or shielded CAT3/5/5e cables (don't use crossover cables!) Note: These analog inputs are 3.3 V tolerant. Do not connect 5 V signals.

Pin number Signal name STM32F407 pin Usage
1 ADC12_IN9 PB1 ADC input for brake pedal
2 ADC12_IN8 PB0 ADC input for throttle pedal
3 ADC12_IN14 PC5 ADC input
4 VCC_OUT +3.3 V supply
5 ADC12_IN4 PC4 ADC input for clutch pedal
6 ADC12_IN7 PA7 ADC input
7 HX711_CLKOUT PE12 Reserved for future use
8 GND / 0 V Ground

X11-lower

Pin 1 is the left-most.
Use with a RJ45 (8P8C) modular connector. Can be used with straight unshielded or shielded CAT3/5/5e cables (don't use crossover cables!) Note: These analog inputs are 3.3 V tolerant. Do not connect 5 V signals.

Pin number Signal name STM32F407 pin Usage
1 Button 15 PC15 Digital input for button
2 ADC123_IN13 PC3 ADC input
3 ADC123_IN3 PC3 ADC input
4 VCC_OUT +3.3 V supply
5 ADC12_IN4 / DAC1 PA4 ADC input (/ DAC output)
6 ADC12_IN5 / DAC2 PA5 ADC input (/ DAC output)
7 ADC12_IN6 PA6 ADC input
8 GND / 0 V Ground

USB Connectors

Connector Usage Notes
X3 USB connector for the STM32F4
X4 USB connector for the IONI

Basic wiring scheme

SimuCUBE basic wiring scheme. Please see the motor position sensor table for the DB15 connector pinout.

RJ45 connector wiring examples

Example of how to wire buttons and analog signals to SimuCUBE.
Easiest way to wire the rj45 connectors are through a terminal block adapter such as this. Items like this can be obtained for example from eBay (try this search).

Internal connector pinouts

EXT-LEDS connector is directly wired to microcontroller I/O pins without any protection devices (such as ESD clamp diodes, or resistors). Any miswiring may cause permanent damage to the drive.
Damage caused through EXT-LEDS connector is not covered by the warranty.
SimuCUBE internal connectors.
Retrieved from "https://granitedevices.com/w/index.php?title=SimuCUBE_pinouts_and_wiring&oldid=6670"