Search results
Create the page "Software" on this wiki! See also the search results found.
Page title matches
- * This EULA governs software provided by Granite Devices from the moment software is installed. ** Install as many copies of software as you need for your own use.7 KB (1,115 words) - 19:17, 18 January 2023
Page text matches
- ===Software=== *[[:Category:Software|Software]] - learn about setup and control software4 KB (504 words) - 19:59, 24 April 2020
- In '''motion control''' this usually means a CNC controller, software, PLC or similar that generates the [[setpoint signal]]s for the drive as we *Software controllers (run on PC)2 KB (300 words) - 19:54, 28 August 2015
- *Easy setup via [[GDtool]] software6 KB (771 words) - 10:17, 5 June 2019
- ...|thumb|GDtool 2.5 with response graphs]]GDtool is a configuration & tuning software for VSD-A and [[VSD-E and VSD-XE|VSD-E/XE]] drives. GDtool 1.0 was a temporary tuning software for [[VSD-A]] in early days before GDtool 2 was introduced.1 KB (173 words) - 22:11, 10 August 2015
- DCtool is a setup software for [[VSD-E and VSD-XE]] in '''DualDC''' operating mode. Compared to [[GDto ...supplied GDflasher software. Needed firmware file is supplied in the same software package.848 bytes (128 words) - 22:12, 10 August 2015
- # Launch Granity software and: # Launch Granity software and:7 KB (1,052 words) - 07:59, 27 April 2017
- | CEN || Require software enable || Tick this option to make drive start in "disabled" state and wait ...nction is wanted. Homing on external command will start homing sequence by software command or via corresponding physical input signal line. ''Homing on power-13 KB (2,085 words) - 18:38, 4 January 2021
- ...fect might be just reduction of noise. Setting TBW to 100-680 Hz activates software filtering of current sense signals thus it will also reduce the hiss.3 KB (486 words) - 10:54, 25 July 2018
- *{{G2.1}} and later: LSF also works with software limits (when {{param|HHL}} and {{param|HLL}} are set and homing is successf ...itches installed but wishes {{param|LFS}} to activate if motor exceeds the software travel limits {{param|HHL}} or {{param|HLL}}. In this case set this option6 KB (901 words) - 07:24, 19 November 2018
- [[File:Granity3dhires.png|600px|right]]Granity is the configuration software tool for Granite Devices motor drives, such as [[IONI]], [[ATOMI]] and [[AR ...15.3 win64.zip|Download Granity 1.15.3 for Windows (This version fixes the software freezing bug) (91 MB)}}8 KB (1,100 words) - 10:56, 14 January 2022
- |Compatible firmware (software)2 KB (329 words) - 13:22, 28 February 2018
- ...l. I have also added X and Y axis limit switches, as EMCO design relied on software limits only. The overheat output signal goes to PLC from stepper controller2 KB (345 words) - 21:13, 10 September 2012
- |notcategory=Software ==Setup software articles==346 bytes (34 words) - 22:21, 17 October 2012
- *Software refuses to connect to the drive *Wrong software being used for the installed firmware. Use only GDtool for single axis firm3 KB (494 words) - 15:33, 17 June 2016
- [[Category:Software]]4 KB (533 words) - 15:34, 19 December 2017
- This is [[Granity]] motor drive configuration & tuning software user guide main page. Please find individual articles below or browse [[:Ca1 KB (196 words) - 14:31, 16 October 2018
- For practical reading software implementation, see devicedeployment.c from SimpleMotion library.3 KB (411 words) - 11:34, 11 October 2018
- ...iguring bus address is required to establish a connection with [[Granity]] software. ...t address between 1 to 32. Device address is a sum of hardware setting and software parameter {{param|SMO}} (IONI only). The address of device is determined at5 KB (675 words) - 09:23, 1 September 2017
- | configtool=No software tools needed6 KB (772 words) - 08:34, 13 May 2022
- ...rives (such as [[Argon (servo drive)|Argon]]) to [[Granity]] configuration software.1 KB (171 words) - 10:59, 17 September 2015
