Difference between revisions of "Argon user guide"
| [checked revision] | [checked revision] |
| Line 2: | Line 2: | ||
{{Disclaimer}} | {{Disclaimer}} | ||
{{ArgonManualNav}} | {{ArgonManualNav}} | ||
| + | {{TOC|right}} | ||
[[File:Dangerelectric.gif|96px|float|right]][[File:Dangermachine.gif|96px|float|right]] | [[File:Dangerelectric.gif|96px|float|right]][[File:Dangermachine.gif|96px|float|right]] | ||
This is the official and latest setup guide of [[Argon (servo drive)]]. Read it through before installing or operating Argon. | This is the official and latest setup guide of [[Argon (servo drive)]]. Read it through before installing or operating Argon. | ||
Revision as of 14:35, 14 August 2013
 | Argon user guide is not yet finished and not safe to rely on. If you already have Argon drives, please wait until this notice has been removed before attempting to operate the device! |
In no event the Product Information or parts hereof shall be regarded as guarantee of conditions or characteristics. The Product Information or any part thereof may also not be regarded as a warranty of any kind. No liability of any kind shall be assumed by Author with respect to Product Information or any use made by you thereof, nor shall Author indemnify you against or be liable for any third party claims with respect to such information or any use thereof.
As content of this Wiki may be edited by user community, Granite Devices Oy or it's affiliates do not take any responsibility of the contents of this Wiki. Use information at your own risk. However, Granite Devices staff attempts to review all changes made to this Wiki and keep information trustworthy.
Without written consent, Granite Devices' Products or Intellectual Property shall not be used in situations or installations where living beings, material property, or immaterial property could be harmed by the operation, features or failures of Product. Products may only be used in a way where hazards like moving parts, electric shock, laser radiation, or fire can't be realized even if the content of this Wiki would suggest otherwise.
This is the official and latest setup guide of Argon (servo drive). Read it through before installing or operating Argon.
NOTE: This guide attempts to be as complete and precise as humanly possible, however it can never be perfect. Writers of this guide are not responsible if possible damages or losses caused by mistakes or lacks of this guide.
IMPORTANT: Argon drive should be installed and operated only by qualified electricians. Dangerous voltages and mechanics are involved and possibility of severe injury or even death is possible in case of installation or usage errors.
CURRENT STATUS: This guide is work in progress and should not be followed until this notice has been removed.
Reading the guide
Read trough the guide by following the outline and follow the hyper links to subtopics provided in the articles. Many useful and important key points are presented as:
 | Electrical hazard warning (safety) |
| Warning/Caution (safety) |
 | Machine danger (safety) |
 | Risk of equipment damage |
 | Info |
 | Tip |
In addition to other documentation, make sure you have carefully read and understood all of the pages containing safety and equipment damage warnings before operating the device:
- Argon firmware releases
- Argon specifications
- Argon supply voltage troubleshooting
- Argon user guide/Braking resistor
- Argon user guide/Drive parameterization
- Argon user guide/Earthing
- Argon user guide/J1 connector wiring
- Argon user guide/J4 connector wiring
- Argon user guide/J5 connector electrical interfacing
- Argon user guide/Power supply safe discharging
- Argon user guide/Wiring
- Argon user guidebook
- Commissioning of KANZ servo motors
- Configuring drive voltage limits FUV and FOV
- FTDI Linux USB latency
- Granity user guide/Connect
- IONI user guidebook
- Overvoltage and undervoltage faults
- Reading and writing an arbitrary parameter with Granity
- Replacing Argon fuse
- SMV2BRK
- Servo drive configuration files
- SimpleMotion V2 port
- SimpleMotion V2 termination with bare cable
Argon introduction
Argon is a servo motor drive designed by Granite Devices. If you are not familiar with the features and specifications of the drive, see following articles:
- Argon (servo drive) - overview & features
- Argon specifications - electrical, physical and operating condition specs
The setup process
Read the page List of things needed for details.
Connect drive to PC with SimpleMotion V2 USB adapter and Granity to test connection, upgrade firmware if necessary and to learn Granity. If you're already familiar with all this, you may skip this step. Read the article Making the first Granity connection
Carefully do the full wiring of the servo system. Consult an qualified electrician if necessary as dangerous voltages will be present. Befower powering up, triple check everything by using multimeter to find short circuits. Read the main article Wiring.
Power-up the system and connet again with Granity. Now set-up the motor to work as intented. See the main article Drive paramerization. If you already have a working configuration to your motor model, you may just load the settings file to the drive.
After motor and drive are fully functional, connect motor to the mechanical load and find the optimum velocity or position control gains. Read the main article Servo motor tuning.
Troubleshooting
In case of troubles, refer to the articles in general troubleshooting category and Argon troubleshooting category.
